Cyber Monday may be over, but great prices are here to stay.
Two-pack of powerful batteries that add a wealth of runtime to tools when used. Convenient button indicates battery level. Provides unmatched quality for optimal and effective power tool use. Batteries charge quickly and work with 18V LXT tools.
The 18V provide sufficient power for a majority of Makita drills and small power tools. Easy to engage and disengage the locking mechanism. Has 6Ah, capacity allowing it told hold its charge for long periods of time. Relatively light.
It can be hard to slot it into Makita chargers.
Battery is easy to insert. Charges quickly and easily on an original Makita charger. Has an impressive lifespan, even with moderate to heavy usage. Comes as a 2-pack of 14.4V batteries that work with Makita 1433, 1434, 1435, 1435F, 192699-A, and 193158-3.
Somewhat difficult to remove from drill. Battery may get hot after extended use.
The sliding design is easy to understand, and the pack locks in place without much pressure. The casing sits nice and flush against the majority of Makita 12V tools. Holds a charge when not in use and has a solid runtime regardless of what tool is being used.
Some users noted that it is a bit expensive compared to other packs.
The plastic housing is shock-absorbing, and each piece is held tight to stop dust from affecting the battery. Has multiple points where the charger locks in to keep it from disengaging when not needed. Has decent runtime even when tools are at max power.
Not compatible with a large variety of Makita tools.
We recommend these products based on an intensive research process that's designed to cut through the noise and find the top products in this space. Guided by experts, we spend hours looking into the factors that matter, to bring you these selections.
Makita has been one of the biggest names in cordless power tools for a number of years. The company’s high-quality drills, saws, impact drivers, and other products have a reputation for durability, so you’ll find that a lot of older models are still in use every day. Because of this, there is a strong demand for Makita replacement batteries, and you’ll find that a number of companies produce them.
There are several factors to keep in mind when shopping for Makita replacement batteries, from device compatibility to voltage to ampere-hours. The quality and price vary considerably between these batteries, so we’ve been making comparisons to provide you with some guidance.
If you’re ready to buy a Makita replacement battery, this article features several of our recommendations. The following buying guide also looks at the technology and prices and discusses your choices in more detail.
Nickel-cadmium: The first widely available rechargeable batteries were nickel-cadmium (NiCd). They were something of a revolution, but they’re heavy, Cadmium is highly toxic, and the battery performance is limited, as demonstrated by Makita’s early range being just 9.6 volts.
Nickel-metal hydride: The next advance was nickel-metal hydride (NiMH). These batteries are more powerful and longer lasting than NiCd batteries, but they’re also more expensive, and care is needed when charging them to maintain performance.
Lithium-ion: The newest technology is lithium-ion (Li-ion), and it is unrivaled for power tools. These batteries can hold more power and deliver it for longer, though they’re currently more expensive than other types. As far as we are aware, all new power tools use Li-ion batteries, underlining their performance advantage.
It’s vital that the Makita replacement battery you choose is compatible with your tool, of course. You need to check part numbers carefully. However, there are several other considerations to keep in mind, too.
Stick with the same chemistry. This is a good idea, and in some cases you have no choice. Early 9.6-volt Makita cordless tools had a slimline NiCad battery that fit up inside the handle, and as far as we know there are no NiMH or Li-ion alternatives.
Makita’s NiMH-powered tools are 12 volt, 14.4 volt or 18 volt and fit in a pack on the end of the handle, which is now common. We did find one adapter that allows you to upgrade to Li-ion batteries, but it only fits 18-volt models.
You cannot fit NiCad or NiMH batteries on Makita Li-ion-powered tools.
Check the minimum voltage. Voltage can be looked at as a rating of the performance available from the tool. There’s no point in trying to put a 9.6-volt battery on a 12-volt tool. It won’t provide the power to drive the motor properly. Theoretically, it ought to be possible to put an 18-volt battery on a 12-volt tool, but it’s easiest and safest to stick with the marked voltage.
Buy the maximum ampere-hours available. If voltage is power, then ampere-hours (Ah) are the fuel. Strictly speaking, it’s a measure of how long the battery can consistently deliver 1 amp of power. Older-style Makita batteries are sometimes rates in milliampere-hours (mAh), but as there are 1,000 mAh in 1 Ah, it’s really the same thing.
In practical terms, a 3.0 Ah battery delivers the same performance as a 2.0 Ah battery in terms of outright power — voltage output — but it will continue to deliver that power for longer. It’s like having three gallons of gas in the tank instead of two.
With NiCd and NiMH batteries, the power starts fading away the minute you start using it. That doesn’t sound particularly bad, but in reality you’re almost never getting peak performance. With Li-ion batteries, though the eventual drop-off is more dramatic, they deliver consistent power for longer.
The bottom line is to always get the highest ampere-hours available. Although mathematically a 4.0 Ah battery should last exactly twice as long as a 2.0 Ah battery, management circuitry usually improves on that, so the 4.0 Ah battery will last at least twice as long and usually considerably longer.
Batteries can also be rated by cycle life: the number of times they can be recharged. However, it’s not a figure you see quoted very often, and because everyone uses their tools differently, it doesn’t have much practical bearing on your decision.
As battery technology has advanced, so recharging times have reduced. Old NiCad batteries always seemed to take hours (and many did). Modern Li-ions recharge much more rapidly.
It’s worth noting that as the ampere-hour rating goes up, so do the recharge times. An 18-volt 2.0 Ah Li-ion battery will charge much faster than an 18-volt 5.0 Ah battery. However, with Makita’s version of the latter (LXT) now charging in well under an hour, we would still opt for that model.
You’ll find cheap Makita replacement batteries for around $20 to $30. It’s what we would expect to pay for a pair of older-style slimline 9.6-volt models that slide up into the handle. You can find Li-ions in that price range, but we would avoid them.
The 12-volt, 14.4-volt and 18-volt NiMH batteries cost around $30 to $40 each. You’ll usually save around $10 if you buy them in pairs.
It’s very difficult to find knockoff alternatives to Makita’s 18-volt LXT Li-ion range. Makita warns against their use, and those we did find are of dubious quality. That leaves you with Makita’s own, which cost anywhere from $80 to $110. They’re pricey, but these are high-performance 5.0 Ah versions, so you’ll never be short of power.
Recharge batteries based on the type. There’s some confusion about whether you should let batteries run all the way down before recharging. It depends on the type. NiCad batteries have what’s called a “memory effect.” For example, if they’re still one-quarter charged when you recharge them, they “remember” that, and only provide a three-quarter charge. This effect gets worse each time, so they need to be “deep discharged” (run as flat as possible) before recharging. NiMH and Li-ion batteries don’t have the same problem, so you can recharge them whenever convenient, as soon as your tool isn’t working at peak performance.
Don’t overcharge the batteries. Overcharging can dramatically reduce the performance of your batteries, particularly NiCd and NiMH types. A short while won’t make much difference, but don’t leave batteries in the charger for any longer than necessary after they’ve reached full charge. Some Makita batteries have circuitry to prevent overcharging, but it’s best not put it to the test. Makita’s Lithium-ion Extreme Technology (LXT) batteries have useful charge indicators.
Keep the batteries at around 60°F. Extreme cold will drain your rechargeable batteries. Never leave batteries in a vehicle or shed where they might freeze because this can cause permanent damage. NiCad batteries are more tolerant than NiMH, and while early Li-ion were susceptible, Makita’s LXT batteries handle the cold surprisingly well.
Don’t store drained batteries. If you’re storing batteries for any length of time, don’t leave them with no charge because they may not “wake up” when you want to charge them again. Experts recommend charging to about 50%. Makita’s LXT batteries, for example, are supplied with 30% charge, which is “for storage purposes only.”
A. Makita warns that non-genuine batteries could perform poorly, catch fire, damage the charger, and so on. Their use will certainly void the tool warranty. Any of these things might be true, but let’s not forget that Makita has a vested interested in selling you its own battery!
We wouldn’t trust cheap knock-off batteries, but quality alternatives can save you a lot of money and should be perfectly safe. The battery cells in some brands we looked at are made by Samsung, a well-known and trusted manufacturer, so we have no problem recommending a variety of non-Makita replacements.
A. It’s impossible to know precisely because it depends on the battery type, the tool it’s fitted to, and the conditions of use. We can make some generalizations, though. NiCad batteries are usually good for around 18 months; NiMH for between two and three years. Batteries in Makita’s latest Li-ion 18V LXT range have a three-year warranty, so clearly the company expects them to last longer. Five years isn’t uncommon. Of course, all of this depends on proper care and recharging.
A. You could save money in theory, but it’s not a five-minute job. You would need a good knowledge of electronics and the right tools (including a soldering iron and glue gun). You need to cut open the existing battery unit, replace the cells inside, then reseal it. It’s not a process we would recommend. When you factor in your time, it’s difficult to assess whether you’re making any real savings.